Sticky
SULDR Forums Supported Printers Printing Questions Scanning Questions General Questions Samsung Installer

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - pi4630

Pages: [1]
1
Scanning / SCX 3400 networked
« on: December 14, 2019, 05:06:19 »
Hi everybody,

so far I had my SCX-3400 connected via USB to my ubuntu 18.04.3. Everything was fine via USB: scanning as well as printing.

Kids and wife asked to use the MFP via network, so I bought a TP-Link PS310U, connected it to the MFP and the router. Printing works. Simple Scan however, doesn't find any device. The MFP has the following address: dnssd://Samsung%20Electronics%20Co.,%20Ltd.%20SCX-3400%20Series-20dfdf._printer._tcp.local/

I run netdiscovery, but couldn't find it:

pasqualino@Asus:~$ /opt/Samsung/mfp/bin/netdiscovery -all --scanner
# DEBUG: Network printers discovery utility

My installed suld  packages are:
suld-driver-3.00.65 (version 3.00.65-4)
suld-network-2 (version 4.00.39-2)
suld-ppd-1 (version 4.00.39-2)

What can I do? Should I try the network-1 package?

Thanks
#pasquale

2
Scanning / SCX 3400 on ubuntu 18.04.1
« on: September 03, 2018, 02:09:36 »
Printer Model = SCX-3400
Linux distro = ubuntu 18.04.1
USB connected
suldr-driver 3.00.65 version 4
suld-network 2
suld ppd 1

I have upated my distro from 16.04 to 18.04 (the above driver version worked flawlessy with the old distro), and now have problems making the scanner work. SimpleScan does not have any scanner entry, VueScan doesn't work neither.

sane-find-scanner yields
found USB scanner (vendor=0x04e8 [Samsung Electronics Co., Ltd.], product=0x344f [SCX-3400 Series]) at libusb:003:004
could not open USB device 0x1d6b/0x0002 at 003:001: Access denied (insufficient permissions)

I don't know about the permission problem above. My user is part of lp.

Edited /lib/udev/rules.d/60-libsane1.rules by adding
# Samsung SCX-3400
ATTRS{idVendor}=="04e8", ATTRS{idProduct}=="344f", ENV{libsane_matched}="yes"

Still to no avail. Any hint?

Thanks
#pi4630

3
General Discussion / Samsung MFP: recommendation needed
« on: November 26, 2015, 08:00:25 »
Hi,

I own a Samsung SCX-3400 MFP and have a good experience with Ubuntu since 12.04 and SULDR packages :)
A friend of mine switched to Linux too recently, and needs a MFP as well. Samsung now sells the M2070 as low budget MFP. I was looking for posts in the Scanning forum and saw that there're some serious issues with scanning and the M2070, right?

Which other current Samsung MFP models would you recommend with Linux and SULDR, where printing and scanning work like a charm?
Thank you.
 

4
Hello,

using ubuntu 12.04 LTS 64 bit with Samsung SCX-3400 and SULDR-packages.
If I use latest driver (4.01.17), I'm able to scan and print documents, pdfs, but not image files (e.g. printing jpegs will fail, i.e. goes to queue and then vanishes).
Viceversa, if I downgrade to 3.00.65, I'm able to print everything, but scanning will fail when attempting to get a scan preview (after a few seconds when the scan starts "Error during read: Error during device I/O") with xsane.

Thanks in advance

5
Hello,

I did follow this procedure (http://www.gaggl.com/2012/04/installing-samsung-multifunction-printer-ubuntu-11-10) but have a partial success: test page prints, as well as pure text document from libreoffice. But JPeGs and documents containing pictures are not printed. I see these jobs ending in queue, processing, but then they vanish, queue vanishes as well and the printer doesn’t react at all.

The instructions above are for 11.10 - but I found that same apply to 12.04.

Any help would be appreciated, thanks.

Pages: [1]
Repository Information Legal Contact Alternative Drivers